Sunday, February 28, 2010

D Ring Belt How Do I Tie A Double D Ring Belt?

Renewal period - Part3

I finally concluded the renewal of my system, the last step was the preparation of the new filter for the pot of mash. There are a bit 'of difference with the previous one and I used a hack saw on the net that works very well and I wanted to share it with those who read these pages.
Finding the T-fitting and threaded stainless steel tube was quite complicated, difficult to work with hydraulic systems are used wherever you prefer brass or stainless zincato.Non I want to open discussions on whether or not it is safe to use brass fittings , I just remember that 99% of the water that flows from your taps at home go for something made of brass which can be the same valve (usually brass), fittings, pipes, etc. .. My choice to use stainless steel is more to issues of miles washability of a Plant Chronicler's done as much as possible of this material and to avoid corrosion problems that the galvanized steel cmq tends to give.

The pattern is the same as the previous one and I think the pictures are understands quite well.
I got a hose, I cut the ends and I removed the hose. The threaded ends
I have not thrown away, I removed the part that held the rubber by a screwdriver (it takes 30 seconds) and then I used to fix the filter with two straps to tee The novelty is the use of a wire, stainless steel also cooked than otherwise the third is all rust, a coiled spring means and then inserted into the filter to give stiffness. This type of filter in fact tend to crush under the weight of the grains and narrow in some areas deformed by inserting the steel wire will avoid all these problems and the filter is of the same form after crush crush. Just take a pen and put a little 'patience to wrap the wire with the same patience and do enter the filter. The threaded part did make me have a turner is a job for 10 minutes starting from a steel bar. A little 'Teflon, otherwise it loses liquid from the threads, and I put everything in 10 minutes. The plant is now ready for a crush test.




















I parametri che userò saranno gli stessi e colgo l'occasione per condividere i miei calcoli visto che nei formu spesso si chiede come prevedere OG e litri finali.

E' piuttosto semplice: mettiamo che voglio arrivare a 23 litri di birra in fermentatore al momento dell'inoculo del lievito, questo significa che devo avere 25 litri a fine bollitura nella pentola ( 2 rimangono sul fondo come resti di proteine e luppoli ), conoscendo il mio tasso di evaporazione con il fornello che uso, ovvero 10 litri in 80min, devo partire da 35 litri pre boil.
Attenti che la OG che calcolate con i vari programmi non si riferisce a 23 litri... but at 25! 2 throw it as a fund ok, but they contain sugar that you extracted cmq! It 's a mistake that I often do. Knowing your efficiency (mine is 70-72% for beer that require more than 5.5 kg of grain and 74-75% for beer that require less grain and therefore are "washed" by most) do count with little programs how many grains you need to get to a certain OG to make 25 liters. To get to 35 liters
pre boil the calculation is as follows: suppose that beer I need to 6kg of grain in total, and I use 3 liters per kg of wheat means that you set in 18-liter mash. What you get
draining the juice from the first extraction is (18-6) = 12 liters per kg of grain in the holds me about one liter of water (but only in my case I have the filter on the bottom, if you have an empty space might be a little 'different calculation).
therefore I need to get to 35 liters (35-12) = 23 liters of spreads. I usually abbbondo a bit 'because I have to consider the water that remains on the bottom of the pan to spread (half liter) and the fact that if you use a little' more than normal flakes act as sponges .. so we always put in more than 1.5 liters. In this hypothetical
total heat cooked as 24.5 liters of water spreads. The control of
litraggi do it using an ordinary ruler, just calibrate the pot in the sense that I know for example that in my 35 liter pot when they reach by the liquid has a height of 32cm from the bottom. Just get an afternoon to score on a sheet liter per liter, which reaches a height of liquid in your pot.
With these simple calculations, and knowing my system I can predict with great precision and end liters OG, the error I have is up to half a liter of wine, and a point on OG.

looks like the system finished ... for the second time!


soon for updates e. .. HAPPY BREWING!

Sunday, February 21, 2010

Causes Of Sore Throats Befroe Periods

TASTING: Pils (or alleged)

As usual when it comes to certain styles should always be given the shortness of calling these beers with your name: ok ok so to the true pilsner decoction, with only Moravian malt, with pure water, with only Saaz .. bla bla bla, you could go on for hours to mention all that bsognerebbe do to be able to speak only of pils. I do not I feel like it, and honestly I find it quite boring to be demanding certain things that would be applied to any style. So this is MY pils and everyone who is comfortable about his business: D.
Besides viewing the list of ingredients you can not deny that deep down there, I tried hard to follow the canons of style.


Then go immediately to the recipe that is obviously very simple recipe for

, end-liter 20.0 (in boiling 30.0)
efficiency 70%, boil 79min.
OG 1.052, IBU: 43.0, EBC: 12;

Malti:
4500 gr Mr.Malt Pilsner, 1,037;
300 gr Mr.Malt Cara-Pils, 1,033;

Luppoli e altro:
60 gr Saaz, 3,7 %a.a., 79 min;
30 gr Saaz, 3,7 %a.a., 30 min;
20 gr Saaz, 3,7 %a.a., 15 min;
10 gr Saaz, 3,7 %a.a., 2 min;

come lievito 3 bustine di Saflager s23 reidratate prima dell'inoculo, la prima fase di fermentazione ( 12 giorni se nn erro) è avvenuta in cantina a una temperatura di circa 8°C, è seguito un diacetil rest di qualche giorno a circa 14°C fino ad arrivare a 80% di attenuazione apparente.

Mi sono impegnato ad usare un'acqua più povera di sali possibile, la Sant. Anna è veramente clean and the only additions I made the mash to achieve a worthy amount of calcium for the conversion (1.7 ppm of calcium seemed risky).
The idea was also groped a double decoction, but the pils malt that I was going to use had become antiquated and use it in the sensitive stages of conversion of the decoction seemed like a suicide in terms of time. Then an infusion usual "normal" with only slight grain protein rest (which was simply the immersion of grains in reality) and then converted to 65 ° C for one hour + mash out.
Speaking a little 'beer itself and using my previous pils, I must say that perhaps I was expecting something more, and many improvements on the paper are actually non è così esageratamente più buona.
Partendo dal colore è ancora un po' troppo carico per i miei gusti, e non è nemmeno molto limpida. Comincio a credere che questo lievito secco non sia poi gran che e che forse con un liquido otterrei qualcosa di meglio.
Le note olfattive sono ancora piuttosto basse in termini di luppolatura, e l'uso di solo saaz non è che abbia portato benefici enormi. E' mio modestissimo parere che un hallertau anche come aroma non mi avrebbe fatto schifo... il saaz è si speziato ma anche troppo lieve nelle note per i miei gusti. Dipende un po' da quello che cercate, se volete una lager maltata in cui il luppolo non deve essere protagonista allora l'uso di solo saaz renderà la vostra birra molto morbida.
The thing that convinces me, however, less has not yet arrived at the dryness that I want. The cleaner water has helped you in terms of taste but despite the apparent 80% mitigation for my taste is not quite dry, but could also be deceived by the yeast that is not very clean, maybe just change that. Excellent
a bitter taste in the strict sense but, they all feel 43IBU although I will not fear for the next to get to 50.
compelesso in every way an excellent beer! In general it is successful, all the notes written above things are not so obvious and intolerable. Certainly will not last long in my basement.

soon for updates e. .. HAPPY BREWING!

Thursday, February 18, 2010

Replacing A F250 Cigarette Lighter

Renewal installation - Part 2

A brief update on the renewal of my system, even if slowly, proceeds from week to week.
As my pot for boiling water has been converted into mash-tun (follow the part about my new filter) I needed a new pot to collect the juice and bring to a boil.
After a little 'research I found this site: http://www.pentoleonline.it/ that sells pots of different sizes and materials at fair prices. Shipping charges are quite expensive, but if you live near Milan, you can pick up in store and save a bit 'of money. I bought the aluminum pans che sul catalogo è descritta come " pentola per salsa tipo nord". Ero piuttosto dubbioso che si trattsse del solito lamierino incosistente che ad ogni lieve pressione cambia forma, invece devo dire che la pentola è molto robusta e ben fatta! unica pecca, i litraggi che riportano loro non corrispondo al litraggio reale perchè fanno il conto prendendo come diametro la sommità della pentola, di dimensioni maggiori rispetto alla base, quindi la loro pentola da 50,2 litri ( quella che ho acquistato io) in realtà contiene circa 42 litri... per le altre pentole in alluminio a diametro costante il valore riportato dovrebbe essere più vicino alla realtà.

Ho eseguito una pre-bollitura della pentola in quanto l'alluminio deve form a protective oxide layer (passivation), which prevents it from dissolving in what will then be cooked inside. Per se, the oxide layer is formed spontaneously in air, however, a boil ensures a good thickness and the removal of aluminum metal eventale this on the pot. Clearly, this is needed only once before use, it is absolutely useful to repeat it several times. Remember that aluminum cookware should be washed with a soft sponge and should not be scratched otherwise damage the protective oxide layer.
The fact that the fund will tend to became yellow during boiling is only because the aluminum oxide forms a porous, it is not absolutely necessary (and indeed it is harmful) to clean the pot making it back shining.

Another thing that I proceeded to do was to make "hard" the cooling coil.
I used copper wire which I twisted atorno tubes (a big job ..). You first need to slightly lengthen the coil and then try to recompress it with pulling the wires twisted in this way, the more snakes noncambierà form. It is not a 'do that particular advantages of course, it's just something I wanted to try to do.

Now to complete the entire system (the second time in eheh pr) I miss only that part of the new filter, I had already done during the summer to retrofit the structure of aluminum bars that I had set the wheels in order to make it easier to transport.
On site there is also the passage from fermenters plastic steel fermenters (which is already available to me) something that probably will do in the summer when I have perhaps a little 'time to devote to the construction of a "fermentation chamber" .


soon for updates e. .. HAPPY BREWING!